Sunday, February 19, 2012

VTP

  





 ON SWITCH 1

Switch>
Switch>
Switch>en
Switch#
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int f 0/1 ?
  <cr>
Switch(config)#int f 0/1
Switch(config-if)#sw
Switch(config-if)#switchport mode tr
Switch(config-if)#switchport mode trunk ?
  <cr>
Switch(config-if)#switchport mode trunk

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Switch(config-if)#ex
Switch(config)#

Switch#sh int tr
Switch#sh int trunk ?
  <cr>
Switch#sh int trunk
Port        Mode         Encapsulation  Status        Native vlan
Fa0/1       on           802.1q         trunking      1

Port        Vlans allowed on trunk
Fa0/1       1-1005

Port        Vlans allowed and active in management domain
Fa0/1       1

Port        Vlans in spanning tree forwarding state and not pruned
Fa0/1       1
Switch#sh vtp status
VTP Version                     : 2
Configuration Revision          : 1
Maximum VLANs supported locally : 255
Number of existing VLANs        : 5
VTP Operating Mode              : Server
VTP Domain Name                 : amit
VTP Pruning Mode                : Disabled
VTP V2 Mode                     : Enabled
VTP Traps Generation            : Disabled
MD5 digest                      : 0x7B 0xD1 0x25 0x53 0xA9 0xF8 0xBA 0xC7
Configuration last modified by 0.0.0.0 at 3-1-93 00:11:06
Local updater ID is 0.0.0.0 (no valid interface found)
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vtp mode c
Switch(config)#vtp mode client ?
  <cr>
Switch(config)#vtp mode client
Setting device to VTP CLIENT mode.
Switch(config)#


ON SWITCH 2 


Switch>
Switch>
Switch>en
Switch#
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int range f 0/1-f 0/2 ?
  <cr>
Switch(config)#int range f 0/1-f 0/2
Switch(config-if-range)#sw
Switch(config-if-range)#switchport mo
Switch(config-if-range)#switchport mode tr
Switch(config-if-range)#switchport mode trunk ?
  <cr>
Switch(config-if-range)#switchport mode trunk

Switch(config-if-range)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up

Switch(config-if-range)#ex
Switch(config)#
Switch#sh int trunk ?
  <cr>
Switch#sh int trunk
Port        Mode         Encapsulation  Status        Native vlan
Fa0/1       on           802.1q         trunking      1
Fa0/2       on           802.1q         trunking      1

Port        Vlans allowed on trunk
Fa0/1       1-1005
Fa0/2       1-1005

Port        Vlans allowed and active in management domain
Fa0/1       1
Fa0/2       1

Port        Vlans in spanning tree forwarding state and not pruned
Fa0/1       1
Fa0/2       1
Switch#sh vtp sta
Switch#sh vtp status ?
  <cr>
Switch#sh vtp status
VTP Version                     : 2
Configuration Revision          : 0
Maximum VLANs supported locally : 255
Number of existing VLANs        : 5
VTP Operating Mode              : Server
VTP Domain Name                 :
VTP Pruning Mode                : Disabled
VTP V2 Mode                     : Disabled
VTP Traps Generation            : Disabled
MD5 digest                      : 0x7D 0x5A 0xA6 0x0E 0x9A 0x72 0xA0 0x3A
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
Local updater ID is 0.0.0.0 (no valid interface found)
Switch#
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vtp domain amit ?
  <cr>
Switch(config)#vtp domain amit
Changing VTP domain name from NULL to amit
Switch(config)#^Z
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#
Switch#sh vtp status
VTP Version                     : 2
Configuration Revision          : 0
Maximum VLANs supported locally : 255
Number of existing VLANs        : 5
VTP Operating Mode              : Server
VTP Domain Name                 : amit
VTP Pruning Mode                : Disabled
VTP V2 Mode                     : Disabled
VTP Traps Generation            : Disabled
MD5 digest                      : 0x16 0xFB 0xEC 0x67 0x59 0x77 0x9E 0x58
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
Local updater ID is 0.0.0.0 (no valid interface found)
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vtp version 2 ?
  <cr>
Switch(config)#vtp version 2
Switch(config)#^Z
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#sh vtp status
VTP Version                     : 2
Configuration Revision          : 1
Maximum VLANs supported locally : 255
Number of existing VLANs        : 5
VTP Operating Mode              : Server
VTP Domain Name                 : amit
VTP Pruning Mode                : Disabled
VTP V2 Mode                     : Enabled
VTP Traps Generation            : Disabled
MD5 digest                      : 0x7B 0xD1 0x25 0x53 0xA9 0xF8 0xBA 0xC7
Configuration last modified by 0.0.0.0 at 3-1-93 00:11:06
Local updater ID is 0.0.0.0 (no valid interface found)
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vtp mode s
Switch(config)#vtp mode server ?
  <cr>
Switch(config)#vtp mode server
Device mode already VTP SERVER.
Switch(config)#


ON SWITCH 3


Switch>
Switch>
Switch>en
Switch#
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#
Switch(config)#int range f 0/1-f 0/2 ?
  <cr>
Switch(config)#int range f 0/1-f 0/2
Switch(config-if-range)#sw
Switch(config-if-range)#switchport mo
Switch(config-if-range)#switchport mode tr
Switch(config-if-range)#switchport mode trunk ?
  <cr>
Switch(config-if-range)#switchport mode trunk

Switch(config-if-range)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up

Switch(config-if-range)#e
Switch(config)#
Switch#
Switch#
Switch#sh int tr
Switch#sh int trunk ?
  <cr>
Switch#sh int trunk
Port        Mode         Encapsulation  Status        Native vlan
Fa0/1       on           802.1q         trunking      1
Fa0/2       on           802.1q         trunking      1

Port        Vlans allowed on trunk
Fa0/1       1-1005
Fa0/2       1-1005

Port        Vlans allowed and active in management domain
Fa0/1       1
Fa0/2       1

Port        Vlans in spanning tree forwarding state and not pruned
Fa0/1       1
Fa0/2       1
Switch#sh vtp st
Switch#sh vtp status
VTP Version                     : 2
Configuration Revision          : 0
Maximum VLANs supported locally : 255
Number of existing VLANs        : 5
VTP Operating Mode              : Server
VTP Domain Name                 :
VTP Pruning Mode                : Disabled
VTP V2 Mode                     : Disabled
VTP Traps Generation            : Disabled
MD5 digest                      : 0x7D 0x5A 0xA6 0x0E 0x9A 0x72 0xA0 0x3A
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
Local updater ID is 0.0.0.0 (no valid interface found)
Switch#
Switch#sh vtp status
VTP Version                     : 2
Configuration Revision          : 1
Maximum VLANs supported locally : 255
Number of existing VLANs        : 5
VTP Operating Mode              : Server
VTP Domain Name                 : amit
VTP Pruning Mode                : Disabled
VTP V2 Mode                     : Enabled
VTP Traps Generation            : Disabled
MD5 digest                      : 0x7B 0xD1 0x25 0x53 0xA9 0xF8 0xBA 0xC7
Configuration last modified by 0.0.0.0 at 3-1-93 00:11:06
Local updater ID is 0.0.0.0 (no valid interface found)
Switch#
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vtp mode t
Switch(config)#vtp mode transparent ?
  <cr>
Switch(config)#vtp mode transparent
Setting device to VTP TRANSPARENT mode.
Switch(config)#ex
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#


 ON SWITCH 4


Switch>
Switch>
Switch>en
Switch#
Switch#
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int f 0/1
Switch(config-if)#sw
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode tr
Switch(config-if)#switchport mode trunk ?
  <cr>
Switch(config-if)#switchport mode trunk
Switch(config-if)#ex
Switch(config)#
Switch(config)#^Z
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#
Switch#
Switch#sh in tr
Switch#sh in trunk ?
  <cr>
Switch#sh in trunk
Port        Mode         Encapsulation  Status        Native vlan
Fa0/1       on           802.1q         trunking      1

Port        Vlans allowed on trunk
Fa0/1       1-1005

Port        Vlans allowed and active in management domain
Fa0/1       1

Port        Vlans in spanning tree forwarding state and not pruned
Fa0/1       1
Switch#sh vtp st
Switch#sh vtp status
VTP Version                     : 2
Configuration Revision          : 0
Maximum VLANs supported locally : 255
Number of existing VLANs        : 5
VTP Operating Mode              : Server
VTP Domain Name                 :
VTP Pruning Mode                : Disabled
VTP V2 Mode                     : Disabled
VTP Traps Generation            : Disabled
MD5 digest                      : 0x7D 0x5A 0xA6 0x0E 0x9A 0x72 0xA0 0x3A
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
Local updater ID is 0.0.0.0 (no valid interface found)
Switch#
Switch#sh vtp status
VTP Version                     : 2
Configuration Revision          : 1
Maximum VLANs supported locally : 255
Number of existing VLANs        : 5
VTP Operating Mode              : Server
VTP Domain Name                 : amit
VTP Pruning Mode                : Disabled
VTP V2 Mode                     : Enabled
VTP Traps Generation            : Disabled
MD5 digest                      : 0x7B 0xD1 0x25 0x53 0xA9 0xF8 0xBA 0xC7
Configuration last modified by 0.0.0.0 at 3-1-93 00:11:06
Local updater ID is 0.0.0.0 (no valid interface found)
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vtp mode c
Switch(config)#vtp mode client
Setting device to VTP CLIENT mode.
Switch(config)#ex
Switch#

 

 

Posted by at

No comments:

Post a Comment

Note: Only a member of this blog may post a comment.

Subscribe to: Post Comments (Atom)